Chevron Grey Matt Wall Panel | 250mm x 2.6m x 8mm (Pack of 4)

Chevron Grey Matt Wall Panels 250mm x 2.6m x 8mm

Chevron Grey Matt wall panels give you a chevron pattern that brings movement and a modern geometric edge to the room, without the cost, mess or upkeep of real tiles. Made from 100% waterproof uPVC, they are ideal for bathrooms, en-suites, shower enclosures, kitchens and feature walls, and there is no grout to discolour, crack or scrub. The matt finish softens reflections for a calm, modern look.

Supplied in packs of 4, each 8mm panel measures 250mm wide by 2.6m long, giving 2.6m² of coverage per pack. The narrower format is easy to handle and cut around windows, pipes and awkward corners, and tongue and groove edges lock each panel tightly into the next for a neat, watertight joint. Fit them straight over existing tiles, plaster or plasterboard with panel adhesive.

Key Features & Benefits

✓ 100% waterproof uPVC, will not rot, swell or grow mould in showers and steam

✓ Tongue and groove edges lock panels together for a tight, near-seamless joint with no grout lines

✓ Chevron pattern design for a high-end look without the cost of real tiles

✓ Pack of 4 covers 2.6m², easy to handle in smaller rooms and tight spaces

✓ Wipe-clean surface, no sealing, painting or regrouting

✓ 10-year guarantee

Installer Benefits

✓ Tongue and groove joints slot together quickly and keep every panel straight and in line

✓ Cut to size with a fine-tooth saw or a sharp utility knife, no tile cutter or wet saw needed

✓ Fit over sound existing tiles on most refurbs, so no stripping out

✓ No grouting or tiling skills needed, most bathrooms can be panelled in a day

✓ Matching trims, panel adhesive and sealant available to complete the job

How Many Panels Do I Need?

Divide the width of each wall by 0.25m and round up to get the number of panels, add around 10% for cuts, then divide by 4 and round up to get the number of packs. Each panel is 2.6m long, so one length covers walls up to 2.6m high.

Example: a bathroom wall 2.0m wide needs 8 panels. Adding 10% for cuts gives 9 panels, so you would need 3 packs.

Where to Use

✓ Bathrooms, en-suites and cloakrooms

✓ Shower enclosures and wet areas (with a proper shower tray)

✓ Kitchen splashbacks and utility rooms

✓ Feature walls in living rooms, bedrooms and hallways

✓ Rentals, hotels, gyms and commercial washrooms

For indoor use only.

Installation

1. Acclimatise. Store the panels flat in the room for 24 hours before fitting.

2. Prepare the wall. The wall must be clean, dry, sound and flat. Panels can go straight over existing tiles, plaster or plasterboard. On uneven or damaged walls, fix timber or PVC battens at no more than 400mm centres first.

3. Fit the trims. Fix the starter, corner and end trims in place first, then cut each panel to length with a fine-tooth saw or a sharp utility knife, keeping the good face up.

4. Bond and slot together. Apply panel adhesive in vertical beads to the back of the panel and fit the first panel into the corner trim. Slide the tongue of the next panel fully into the groove of the one before and press it firmly to the wall. In showers and wet areas, run a thin bead of silicone along the tongue before joining for a fully watertight seal. When fixing to battens, screw or staple through the tongue so the next panel hides the fixing. Leave a 3 to 5mm expansion gap at the top and bottom.

5. Finish. Seal the bath or shower tray junction and internal corners with sanitary silicone.

Heavy fittings such as towel rails and shower risers should be fixed through the panel into the wall behind, then sealed with silicone.

Care

Wipe clean with warm soapy water or a mild, non-abrasive cleaner. Avoid solvent-based cleaners, scouring pads and wire wool, as these can dull or scratch the surface.

Frequently Asked Questions

Can I fit these panels over my existing tiles?
Yes, as long as the existing tiles are sound, flat and clean. Bond the panels on with panel adhesive, so most refurbs need no stripping out.

Are the joints waterproof?
Yes. The tongue and groove joint locks each panel tightly to the next with no grout lines. In showers and wet areas, a thin bead of silicone along the tongue before joining makes every joint fully watertight.

Can I use them inside a shower enclosure?
Yes. The uPVC panels are 100% waterproof. Seal the corners and the join to the shower tray or bath with sanitary silicone. They are for walls only and should not be used on floors.

How do I cut the panels?
Use a fine-tooth saw or a sharp utility knife, cutting with the decorative face up. For cut-outs around pipes and sockets, drill a pilot hole and finish with a jigsaw.

What guarantee do they come with?
Our wall panels carry a 10-year guarantee.

Product Specifications

Brand: Duraklad

Design: Chevron Grey Matt

Material: uPVC

Thickness: 8mm

Panel Width: 250mm

Panel Length: 2.6m

Coverage per Panel: 0.65m²

Pack Quantity: 4

Coverage per Pack: 2.6m²

Edge Profile: Tongue and groove

Waterproof: Yes, 100%

Use: Indoor walls

Guarantee: 10 years